New in stock January 2020

Solid rivet 2.5x8 TGL 0-660-Mu 8

Riga 16, Werhovina piston 38,50 for 10mm gudgeon pin

Riga Delta piston + piston rings + gudgeon pin + circlips 38,75 for 12mm gudgeon pin

Riga 16, Werhovina piston + piston rings + gudgeon pin + circlips 39,00 for 10mm gudgeon pin

Ring gear, loose (chormed) 34 teeth SR1, SR2 - 12 drillings

Handlebar locking screw with wedge

Rubber sleeve for ignition cable - water protection cap

Crankshaft complete IWL SR59 Berlin (bronze bushing on top, needle bearing at bottom) refurbished

Process time 6-20 weeks, depending on order situation.
The prize refers to the refurbishment of your own crankshaft. If no replacment part is delivered or if the crankshaft is defect, an additional 75,- € must be paid as a deposit.

Crankshaft complete RT 125/1, 125/2, IWL Pitty, IWL SR56 Wiesel (bronze bushing on top, needle bearing at bottom, 15mm gudgeon pin) refurbished

Process time 6-20 weeks, depending on order situation.
The prize refers to the refurbishment of your own crankshaft. If no replacement part is delivered or if the crankshaft is defect, an additional 75,- € must be paid as a deposit.

Crankshaft complete RT 125/3 (bronze bushing on top, needle bearing at bottom) refurbished

Process time 6-20 weeks, depending on order situation.
The prize refers to the refurbishment of your own crankshaft. If no replacment part is delivered or if the crankshaft is defect, an additional 75,- € must be paid as a deposit.

Clutch hand lever, long

Attention – sample image, you will not get the parts on display!

Clutch hand lever, short

Attention – sample image, you will not get the parts on display!

Exhaust manifold - chromed - SR50, SR80

Mounting rubber with round support for flasher unit

ETZ125, ETZ150, ETZ250

Tool box

Locking plate 8-FSt (DIN 6799) - burnished

Thrust washer 32,4x40x1,5 - for differential SD50

10x double bridges (brass) for terminal board 8800.1 - for Mokick and motorcycle

10x single bridges (brass) for terminal board 8800.1 - for Mokick and motorcycle

Piston complete S70, 45,21 Original MEGU

Original DDR piston may only be sold in connection with a cylinder refurbishment!

Pedal shaft

Fork gear selector

S51,SR50

Scraper rubber for crank disc fixed length 100cm Wartburg P311, Trabant P601, IFA F9

Kickstarter shaft S51,SR50,KR51/2

Rubber handle grip , left hand

Bowden cable, accelerator cable (BVF) - black

KR51/1, KR51/2, SR4-2, SR4-3, SR4-4

Support for front silencer Wartburg 353

Left side pannier, complete

Attention – sample image, you will not get the parts on display!

Carrier new KR51/1, Star, S50, Duo 4/1

Inlet manifold

TS 250, 250/1

Brake shoe c/w lining

For RT 125/2 from chassis.-Nr.: 5002389 MZ 500 R, NR, VR

Radial shaft seal NJK 14x30x7 - FPM - Viton - brown- dustlip

Hand brake lever, long version

Attention – sample image, you will not get the parts on display!

Deposit for inlet manifold TS 250 TS 250/1, will be refunded if regenerable inlet manifold is submitted

4x Friction lining, (Clutch disk A12) Simson

Safety lock - cylinder lock with 2 keys

Repair kit for rear suspension, straight suspension, struts - AWO T 425 left

scope of delivery:
1 x Castle nut, galvanized: 40930
1 x Set screw for rear axle: 40945
1 x Felt washer: 40943
1 x Guide tube: 40921
1 x Screw connection hex socket for rear strut - AWO T: 42013
1 x Cover cap, Aluminium for suspension AWO-T 425 - left: 40046
1 x Suspension spring: 40946
2 x Guide bush, Pertinax - bush for rear suspension: 40950
2 x Rubber buffer end stop: 40923

Wiring harness AWO T with brake light and sidecar exit

Contact bridge complete, hood contact IWL Wiesel, Berlin, plug, plug connection

Clamping element 1,0mm / Blower Engine, V-Belt IWL SR59, Troll

Guide pin for brake pads

Headlamp housing NVA with cutout for speedometer and cover for headlamp

without speedometer and ignition lock
storage marks

Front lens for turn signal, handlebar turn signals

Rear lens for turn signals, handlebar turn signals

S51,KR51/2 refurbishment of your cylinder, incl. original piston, gudgeon pin, piston rings and circlips

The prize refers to the drilling, honing and chamfered edges, processing time approx. 2-3 weeks.

Crankshaft ES300 refurbished

The prize refers to the refurbishment of your own crankshaft.
Process time 3-6 months, depending on order situation.

Bowden cable, clutch cable, black Domino armature - S53, S83 - Habicht

Clutch cable line MS125RS

Bowdencable for starter / choke S53, S83 - Domino armature, Bing carburetor

Starter cable line

Bowden cable to distributor

Clutch cable line

Bowden cable, starter cable

Bowdencable for throttle valve S53 / S83

Rubber bushing for spark plug connector - water protection cap . measures: length 48mm, inside Ø13mm, for plug lead Ø7mm

Clutch cable line MS125

deposit for clutch cover, IWL SR59 "Berlin", will be refunded if regenerable clutch cover is submitted

Ignition switch 6V

Ignition lock

Bowden cable, accelerator cable (Bing-Magura)

S53CX,S83CX

Bowden cable, starter cable with Domino armature - SD50 and SR50, SR80 Star Classic

Hook, for luggage carrier strap Simson and MZ

Distance piece for wheel spindle, front, 21mm long,SB,S53OR,S83OR

Ignition key