New in stock April 2021

SET fastening throttle twist grip (flat spring, stud, SKM M6, spring washer B6)

Cable set for turn signals (handlebar) for Schwalbe KR51 and SR4- / birdseries

Speedometer cable - 850 long - S51

Crossbar, galvanized+primed - for front part - KR51/2

Cover for single seat bench, painted coblat blue metallic - SRA25

Cover for rear carrier, painted pearl white metallic

Cover for rear carrier, painted tornado red

Cover for rear carrier, painted signal white

Cover for rear carrier ruby metallic

Mechanical rev-counter Ø48mm until 12000 rpm, Gehäuse with light slit, white dial

Ignition coil MFM 14 - 1209

Hooded jacket, black/red, size: L - motif: SIMSON - 80% cotton/ 20% polyester

Hooded jacket, black/red, size: XXL - motif: SIMSON - 80% cotton/ 20% polyester

Hooded jacket, black/red, size: XXXL - motif: SIMSON - 80% cotton/ 20% polyester

Hooded jacket, black/blue, size: S - motif: SIMSON - 80% cotton/ 20% polyester

Hooded jacket, black/blue, size: XS - motif: SIMSON - 80% cotton/ 20% polyester

Hooded jacket, black/blue, size: XXL - motif: SIMSON - 80% cotton/ 20% polyester

Hooded jacket, black/blue, size: XXXL - motif: SIMSON - 80% cotton/ 20% polyester

AMAL - idle jet 39

Display unit Facomsa - speedometer + r.p.m. counter - Simson 125

Cover for rear carrier, painted zinc yellow

Front fairing internal, ABS structured, graphit black - SRA50

Carrier on rear wheel - tricycle SD50

Rear spoiler - ABS, raw part

Rocker panel right hand side, cobalt blue metallic

Middle cover left black

Cover for glove compartment graphit grey - SRA50

Rear brake backing plate - raw - with bolt - Simson tricylce SD 50

Wheel rim 2,25x23 (1,35x19) STEEL chrome (Brand Radaelli) SR2, SR2E

Piston complete Ø58,00 K20 (4.excess) TS150

Stop and tail light 8522.7 - chromed housing - TR150

Glass - lens - identity plate glass - fits MZ ES, TS, TR150 - for round taillight

Lens cap for stop and tail lamp, Ø100mm, red, including two screws, gaskets and washers TS, S50, S51, S70, KR51/2

Lens cap for stop light and stop and tail lamp - with E testmark!

Half shell, glavanized - for M53-engine - KR51/1, Duo 4/1, SR4-1, SR4-2

Talkcum 500g shaker

Tube VeeRubber 16" 3,25/3,50

Clip spring for gas clamp SR2E

Carburetor 27KN1-1 (ES 250 Doppelport) regenerated

Regenerated Carburetor with new nozzles, jet holder, jet needle / partial load, slide. In exchange for a regenerable 27KN1-1 carburetor. (deposit 130,-€)
With BVF data sheet

Monoblock-Starting device carburettor 22N1-3

BVF data sheet.

Insert adaptor complete 2923 150ccm

Insert adaptor complete 2935 125ccm

Carburetor 24KN1-1 (IWL SR59 Berlin) regenerated with swivel connection

Regenerated Carburetor with new nozzles, jet holder, jet needle / partial load, slide. In exchange for a regenerable 24KN1-1 carburetor. (deposit 65,-€)
With BVF data sheet

Bowden cable, hand brake - grey - flat handlebar

ETS125/1, 150/1, TS125, 150, 250; ES125, 150, 125/1, 150/1

Bolt for cylinder fastening

ES175/2, ES250/2, ETS250

Bowdencable (grey) Starter/choke (BVF)

837x750x38
KR51/2 (Made in Germany)

Complete reconditioning of your crankshaft ETZ 125, 150

The prize refers to the refurbishment of your own crankshaft, processing time approx. 2-3 weeks.

Complete reconditioning of your crankshaft TS 250/1

The prize refers to the refurbishment of your own crankshaft, processing time approx. 2-3 weeks.

Pair cover caps for rubber gaiter - S51, S70, S53, S83, SR50, SR80

Deflector piston complete 68,50 K20 (1st excess) AWO 425T

Piping for glass edge yard good

Fillister head screw with internal hex M6x8 A2

Brake drum front

Rotor

Brake anchor plate, Set, right hand side

Right foot rest carrier, Rotax V- white

Filter

Holder for ignition lock, old version Trabant bucket car

Knob for windscreen wiper, round, Trabant, Wartburg, Barkas

Knob for head lamp switch, round, Trabant, Wartburg, Barkas

Rotary head lamp switch

Cap for round windscreen washer tank

Plastic nut for light / windscreew wiper knob

Engine mountig, complete, front (oval mounting)

Engine mountig, complete, rear (round mounting)

Distributor M10x1 TGL 29985/07

Retaining for oil guide for crankshaft fits

ETZ 250,251/301; TS 250/1 (up to engine number 2344419)

Retaining ring for crankshaft bearing (wire)

ETZ 250,251/301; TS 250/1 (From engine number 2344420)

Flat washer on handlebar

Speedometer sheet black

Top flange support strut right hand side - not primed - S50, S51, S53, S70, S83 - B, C street design, TS50

Rear brake hose